Close Window  X 
swatch
Color samples are not available for painted colors. Metallic paint colors have tiny silver fleck in the paint which we have tried to represent on the metallic color samples. They are by nature a semi-gloss. Solid colors are full gloss unless requested. If you need exact colors we can color match Sherwin Williams, PPG and Pantone numbers for $20 per color. Colors on computer monitors will vary widely due to the type of monitor and the graphics card. We do not guarantee colors shown on this website will match actual product.
swatch
Color samples are not available for painted colors. Metallic paint colors have tiny silver fleck in the paint which we have tried to represent on the metallic color samples. They are by nature a semi-gloss. Solid colors are full gloss unless requested. If you need exact colors we can color match Sherwin Williams, PPG and Pantone numbers for $20 per color. Colors on computer monitors will vary widely due to the type of monitor and the graphics card. We do not guarantee colors shown on this website will match actual product.

METAL FINISHES:
These are the finishes available for the metal itself. Satin, also known as brushed, applies a decorative linear brushed appearance to the face of the metal. This can be applied to all flat face letters and numbers but cannot be applied on round or bevel faced letters such as Architectural bevel face and Roman Round Face. All round and bevel face will have a bead blasted texture applied as in the picture of the "G" at the top of this page. Polishing cannot be accomplished on Cast Aluminum. All Satin and bead blasted finishes receive a clear coat to protect them against the toughest weather. These letters are outdoor quality and carry a manufacturer's lifetime warrantee.

ANODIZED COLORS:
Anodizing is a chemical process that hardens the topmost layer of the aluminum while at the same time imparting a color to the metal. Anodized aluminum is impervious to weather and requires no clear coat. The anodizing process used is known as type-11 or architectural grade anodizing which will last a lifetime in any weather conditions. These letters are outdoor quality and carry a manufacturer's lifetime warrantee.

BAKED ENAMEL COLORS:
Painted in professional spray booths with architectural grade, UV resistant, acrylic polyurethane which is very tough, long lasting and wont fade, crack or peel under normal use. There is a full range of painted colors available, and we can also custom color match Sherwin Williams, PPG and Pantone colors for an Additional $20 per color. These letters are outdoor quality and carry a manufacturer's lifetime warrantee.

Close Window  X 
Sort the list on tab one

Sort By Price (lowest first)
Sort By Price (Highest first)
Sort Alphabetically by Size

Sort by Size
List will only include the fonts that have a
size specified in the selection box above.

Sort By Type
List only includes the type selected.
Lowercase only list may not have lower case letters in all sizes.
Showing all fonts sorted alphabetically
 
Close Window  X 
Help shows here when images are moused over
SignLetterSource.com
Manufacturer & Distributor since 1999
Products ship from various locations
including-Boston-Virginia-Chicago-Minnesota-Iowa-Texas-Montana and Nevada
cart Shopping Cart:   $0.00
Contact Us
Cast Aluminum Sign Letters
  • Ordering Page
  • Video
  • Price Chart
  • Mounts
  • Gallery
  • About
helpStep 1 helpStep 2 helpStep 3 helpStep 4
Enter Letters - Numbers - Punctuation Choose a Finish Choose a Style/Font
Uppercase
Height
Line 1
arrow
Line 2
arrow
Line 3
arrow
Line 4
arrow
Show tooltip help   help Matte Finish(+15% except metallics)  
Click here to
Watch Product Video
INFO Lowercase Height Letter Depth Uppercase Price Lowercase Price Line Total Pattern Price Total Price GRAND TOTAL
Line 1             $0.00 $0.00
help Alignment help Backgrounds (design use only) Update Display Automatically
                              
Your sign letters display here in the chosen font
Step 5: Select Mounting Hardware and Mounting Pattern
  helpMounting Choices helpStud Length helpSpacer/Stand Off helpMounting Pattern
Line 1
arrow
Line 2
arrow
Line 3
arrow
Line 4
arrow
Total Characters  
Cart Subtotal
Total Cost for Characters  
Mounting Pattern  
Total this page  
Qty
*Quantity is applied to ALL lines

Content on this page requires a newer version of Adobe Flash Player.

Get Adobe Flash player


Holding space for price table

Installation Hardware

Flush Stud Mount

Flush Mounting studs are set in adhesive cement. There is no space between the letter
and the surface.. A mounting pattern is highly recommended to locate the correct places to drill. Once the holes are drilled, screw studs into the stud blocks being careful not to over tighten, then fill the holes with silicon caulk, coat the studs and push the assembly into the wall up to where the stud block meets the wall surface.

 

spacer mount Projected Spacer Mounting Studs are set in adhesive cement. Pre-cut spacers are inserted between the letter and the mounting surface. A mounting pattern is highly recommended to locate the correct places to drill. Once the holes are drilled, screw studs into the stud blocks being careful not to over tighten, then fill the holes with silicon caulk, coat the studs and push the assembly into the wall up to where the stud block meets the wall surface.
jam nut mount Projected Jam Nut Mounting. Studs are set in adhesive cement. Stainless steel jam nuts are inserted between the letter and the mounting surface. A mounting pattern is highly recommended to locate the correct places to drill. Once the holes are drilled, screw studs into the stud blocks being careful not to over tighten, then fill the holes with silicon caulk, coat the studs and push the assembly into the wall up to where the stud block meets the wall surface.
flush metal mount Flat Metal Wall Mounting. Where you have access to the rear of the wall, washers and nuts are used on both sides of wall.
corrugated metal mount Corrugated Mounting. Studs are set using jam nut on front and back of corrugation.
bottom stud mount Bottom studs are available on 3/8" and 1/2" thick letters over 4" tall. For letters over 8" in height, some form of tie backs will be required to mount this outside. Pleaase check with your local city ordinence before purchasing.
bottom rail Similar to a bottom stud, the rail mount includes a length (8ft max) of "C" channel aluminum that tie all your letters together on a single line. Restrictions still apply for tie backs on letters over 8" tall in outdoor use.
rail mount Double sets of rails can be used to span spaces or for uneven surfaces such as corrugated buildings. We provide rails and bolts, max. 8ft. Extra costs apply.

 

8" and 6" Arial Bold Letters with a Medium Bronze Anodized Finish
8" and 6" Arial Bold Letters with a Medium Bronze Anodized Finish

10" Avant Garde Medium Letters with a Satin Aluminum Finish.
10" Avant Garde Medium Letters with a Satin Aluminum Finish.

10", 8" & 6" Futura Letters with a Satin Aluminum Finish.
10", 8" & 6" Futura Letters with a Satin Aluminum Finish.

10" Palatino Letters with a Natural Satin Aluminum Finish.
10" Palatino Letters with a Natural Satin Aluminum Finish.

12" & 9" Times New Roman Letters with a Painted Duranodic Bronze Finish.
12" & 9" Times New Roman Letters

Cast Bronze and Cast Aluminum Letters

Cast Metal Letters

WHEN A SENSE OF PERMANENCY AND DEPTH IS REQUIRED on professional offices, universities and government buildings – Gemini bronze and aluminum cast metal letters offer the depth you need. With 12 different finishes including polished, oxidized or anodized (using Aluminum Anodizers Council and American Institute of Architects guidelines); you can get the classic look and deep dimension of cast metal letters for less than what you would expect to pay for such quality.

Cast metal letters are the pinnacle in dimensional lettering; offering greater dimension than solid sheet flat cut out letters at a cheaper price. Cast metal letters establish a sense of permanency wherever they are installed and convey an image of success about the company that utilizes them in its signage.

Most of our cast metal letters come in flat face designs with the exception of the Architectural font which is bevel faced and the Roman Round font which has a round face.

When your looking for a heavy metal sign letter with lots of dimensional thickness and relativly low cost, a Cast Aluminum or Brass sign letter will be considerably cheaper than a similar size sign letter that has been cut out from solid sheet.

 

Cast metal letters are made in two distinct metals. Both Cast Aluminum letters and Cast Bronze letters are made from mercury and lead free prime ingots, cast in virgin sand molds that produce faces and returns that are pit and blemish free.

There are currently 60 distinctive styles to choose from, many with lower case. There are 12 metal finishes and 45 baked enamel colors. Additionally, we can custom cast your special font, your logo's and your designs.

Custom painted colors are also available using PMS matching or using a manufactures color such as Sherwin Williams, PPG, etc.

For a quick overview of pricing please see our pricing chart by clicking on the link at the bottom of this page. Interested in buying Cast Metal sign letters? you can configure and purchase this type of letter online
Cast AluminumCast Bronze

CONTACT  | ABOUT US  |  ORDER STATUS   |   SHOPPING CART   |  INSTALLATION INSTRUCTIONS  |  HOME
COPYRIGHT © 2010 MONTANA LETTERING INC.      PRIVACY NOTICE

 

instructional video